Influence of plasma-assisted ignition on flame propagation and performance in a spark-ignition engine

Lean-burn is an attractive concept for reasons of high thermal efficiency and low nitrogen oxide (NOx) emissions, however, successful implementation in spark-ignition (SI) engines turned out to be challenging because of misfire or partial burn caused by attenuated flame propagation. In order to overcome this issue, microwave-assisted plasma ignition system (MAPIS) has been applied in combustion systems. The MAPIS consists of a conventional ignition coil, a non-resistor spark plug, a mixing unit, a waveguide, and a magnetron (2.45GHz, 3kW). A series of experiments was carried out to understand discharge characteristics and to validate its performance in a constant volume vessel as well as in a single-cylinder spark-ignition engine. The fundamental investigation based on optical emission spectroscopy and flame imaging showed that the ejection of the microwave was beneficial to produce more reactive species such as OH and O radicals thanks to higher electron temperature than conventional spark ignition. The lean limit was able to be extended up to an equivalence ratio of 0.5 based on a larger initial flame kernel size with MAPIS in the vessel test. Meanwhile, in the engine test, combustion stability was noticeably improved showing smaller cycle-to-cycle fluctuations in in-cylinder pressure. Improvement in fuel efficiency up to 6% could be achieved by stable operation under fuel-lean conditions. In terms of emissions, MAPIS was advantageous to reduce carbon monoxide (CO) emissions by promoting more complete combustion

Review on Plasma-Assisted Ignition Systems for Internal Combustion Engine Application

Due to the depletion of conventional petroleum-based fuels and increasing environmental concerns, industries have been developing new combustion technologies with acceptable cost ranges and minimum system modifications for consumers. Among many approaches, the utilization of plasma ignition systems is considered as a promising pathway to achieve greener transportation while maintaining conventional internal combustion engine systems. Plasma contains highly reactive radicals, and those have a great potential of enhancing chemical reactions that are beneficial for reducing carbon emissions. The primary objective of this paper is to provide an overview of currently available plasma-assisted combustion systems including recent achievements in research and development, and technical challenges for successfully implementing a new ignition system. This review will introduce various plasma-assisted combustion approaches from worldwide projects, covering non-thermal and thermal plasma systems in internal combustion engines

Fuel temperature and injection pressure influence on the cold start GDI sprays

Cold start in gasoline direct injection engines (GDI) is a critical issue that significantly impacts fuel consumption and emissions. Therefore, it is essential to investigate and improve the spray and air-fuel mixing processes during cold starts. This study employed a complimentary set of optical diagnostic techniques, including line-of-sight(extinction, Schlieren, and long-distance microscopy) and 3D computed tomography (CT), to characterize and understand the cold-start spray dynamics under various fuel temperature and injection pressure conditions. The experiments were conducted in a constant volume spray vessel and the fuel temperature was varied using a coolant circulator, with temperatures reaching as low as -7 °C to simulate cold-start conditions. The cold fuel exhibited longer liquid/vapor penetration lengths compared to hot fuel under low injection pressure conditions. This deterioration in spray characteristics was attributed to the attenuated fuel evaporation and reduced entrainment of ambient air. The 3D spray visualization obtained through the CT algorithm, particularly the cut plane images, revealed that plumes with low fuel temperatures had narrower individual plume widths, resulting in minimized plume-to-plume interaction. Microscopic imaging further confirmed this observation which showed separate plumes in the near-nozzle region for cold fuel conditions. Meanwhile, hot fuel under high injection pressure conditions exhibited complete plume collapsing, leading to a significant amount of liquid fuel remaining in the spray core. The liquid penetration reached 70 mm during the injection period, potentially can cause wall wetting on the piston top or cylinder wall. Based on the experimental findings, this study suggests the application of multiple injections with a moderate level of injection pressure for optimized engine performance and reduced emissions during cold starts

Magnetic properties and high frequency characteristics of FeCoN thin films

(Fe65Co35)N soft magnetic thin films were prepared by reactive RF magnetron sputtering with the sputtering power of 100 W on thermally oxidized Si substrate in various nitrogen partial pressures (PN2). A strong uniaxial in-plane magnetic anisotropy with the easy-axis coercive field as low as 1∼2 Oe was observed in films grown at PN2 in the range from 3.3% to 5.5%. The saturation magnetizations for those films were about 20 KG. Outside this range, almost isotropic magnetization curves were observed. Vector network analyzer and grounded coplanar waveguide were used to measure the ferromagnetic resonance (FMR) signals up to 25 GHz. The FMR signals were detected only in anisotropic films and their FMR frequencies were well fit to the Kittel formula. The obtained g-values and damping parameters at magnetic fields >20 kOe for films grown at PN2 of 3.3%, 4.8% and 5.5% were 1.96, 1.86, 1.92 and 0.0055, 0.0047, 0.0046, respectively. This low damping factor qualifies FeCoN thin films for high-frequency applications

Effect of Divided Exhaust Period in a High Efficiency TGDI Engine

The divided exhaust period (DEP) concept was applied to a high-efficiency gasoline engine and its impact on various engine performance aspects were investigated. To this end, key design parameters of DEP components were optimized through 1-D engine simulation. The designed DEP components were fabricated and experimental verification was performed through an engine dynamometer test. The developed DEP engine shows suitable performance for electrified vehicles, with a maximum thermal efficiency of 42.5% as well as a wide sweet spot area of efficiency over 40%. The improvement in thermal efficiency was mainly due to a reduction in pumping loss. Notably, the reduction in pumping loss was achieved under high exhaust gas recirculation (EGR) flow conditions, where further improvements in fuel consumption could be achieved through a synergistic combination of DEP implementation and high dilution combustion. Furthermore, a significantly improved catalyst light-off time, uncharacteristic in turbocharged engines, was confirmed through a simulated cold-start catalyst heating engine test